收藏本站
Data Sheet
ADE7880
t 1
t 2
t 3
MCU
INTERRUPT
FLAG SET
IRQx
PROGRAM
SEQUENCE
JUMP
TO ISR
GLOBAL
INTERRUPT
MASK
CLEAR MCU
INTERRUPT
FLAG
READ
STATUSx
WRITE
BACK
STATUSx
ISR ACTION
(BASED ON STATUSx CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
JUMP
TO ISR
Figure 98. Interrupt Management
t 1
t 2
t 3
MCU
INTERRUPT
FLAG SET
IRQx
JUMP
(BASED ON STATUSx CONTENTS) GLOBAL INTERRUPT TO ISR
PROGRAM
SEQUENCE
JUMP
TO ISR
GLOBAL
INTERRUPT
MASK
CLEAR MCU
INTERRUPT
FLAG
READ
STATUSx
READ
PHx
WRITE
BACK
STATUSx
ISR ACTION ISR RETURN
MASK RESET
Figure 99. Interrupt Management when PHSTATUS, IPEAK, VPEAK, or PHSIGN Registers are Involved
SERIAL INTERFACES
The ADE7880 has three serial port interfaces: one fully licensed
I 2 C interface, one serial peripheral interface (SPI), and one high
speed data capture port (HSDC). As the SPI pins are multiplexed
with some of the pins of the I 2 C and HSDC ports, the ADE7880
accepts two configurations: one using the SPI port only and one
using the I 2 C port in conjunction with the HSDC port.
Serial Interface Choice
After reset, the HSDC port is always disabled. Choose between
the I 2 C and SPI ports by manipulating the SS/has pin after
power-up or after a hardware reset. If the SS/HSA pin is kept
high, then the ADE7880 uses the I 2 C port until a new hardware
reset is executed. If the SS/HSA pin is toggled high to low three
read using either the I 2 C or SPI interfaces. The HSDC port
provides the state of up to 16 registers representing instantaneous
values of phase voltages and neutral currents, and active, reactive,
and apparent powers.
Communication Verification
The ADE7880 includes a set of three registers that allow any
communication via I 2 C or SPI to be verified. The LAST_OP
(Address 0xEA01), LAST_ADD (Address 0xE9FE) and
LAST_RWDATA registers record the nature, address and data
of the last successful communication respectively. The
LAST_RWDATA register has three separate addresses
depending on the length of the successful communication.
Table 24. LAST_RWDATA R egister L ocations
times after power-up or after a hardware reset, the ADE7880
uses the SPI port until a new hardware reset is executed. This
manipulation of the SS/HSA pin can be accomplished in two
ways. First, use the SS/HSA pin of the master device (that is, the
Communication type
8-Bit Read/Write
16-Bit Read/Write
24-Bit Read/Write
Address
0xE7FD
0xE9FF
0xE5FF
microcontroller) as a regular I/O pin and toggle it three times.
Second, execute three SPI write operations to a location in the
address space that is not allocated to a specific ADE7880 register
(for example 0xEBFF, where eight bit writes can be executed).
These writes allow the SS/HSA pin to toggle three times. See the
SPI Write Operation section for details on the write protocol
involved.
After the serial port choice is completed, it needs to be locked.
Consequently, the active port remains in use until a hardware
reset is executed in PSM0 normal mode or until a power-down.
If I 2 C is the active serial port, Bit 1 (I2C_LOCK) of the CONFIG2
register must be set to 1 to lock it in. From this moment, the
ADE7880 ignores spurious toggling of the SS pin and an eventual
switch into using the SPI port is no longer possible. If the SPI is
After each successful communication with the ADE7880 , the
address of the register that was last accessed is stored in the
16-bit LAST_ADD register (Address 0xE9FE). This is a read
only register that stores the value until the next successful read
or write is complete. The LAST_OP register (Address 0xEA01)
stores the nature of the operation. That is, it indicates whether a
read or a write was performed. If the last operation is a write,
the LAST_OP register stores the value 0xCA. If the last
operation is a read, the LAST_OP register stores the value 0x35.
The LAST_RWDATA register stores the data that was written
or read from the register. Any unsuccessful read or write
operation is not reflected in these registers.
When LAST_OP, LAST_ADD and LAST_RWDATA registers
are read, their values are not stored into themselves.
the active serial port, any write to the CONFIG2 register locks
the port. From this moment, a switch into using the I 2 C port is
no longer possible. Once locked, the serial port choice is
maintained when the ADE7880 changes PSMx power modes.
The functionality of the ADE7880 is accessible via several on-
chip registers. The contents of these registers can be updated or
Rev. A | Page 73 of 104
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADE7953EBZ BOARD EVAL FOR ADE7953
EVAL-ADF4002EBZ1 BOARD EVAL FOR ADF4002
EVAL-ADG788EBZ BOARD EVALUATION FOR ADG788
EVAL-ADM1021AEB BOARD EVAL FOR ADM1021
EVAL-ADM1023EB BOARD EVAL FOR ADM1023
EVAL-ADM1031EB BOARD EVAL FOR ADM1031
EVAL-ADM1062TQEBZ BOARD EVALUATION FOR ADM1062TQ
EVAL-ADM1075CEBZ BOARD EVAL FOR ADM1075
相关代理商/技术参数
EVAL-ADE7880EBZ 制造商:Analog Devices 功能描述:ADE7880, ENERGY METER, 3 PH, SPI, I2C, E
EVAL-ADE7913EBZ 制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Isolated, Sigma-Delta ADC with SPI
EVAL-ADE7953EBZ 功能描述:BOARD EVAL FOR ADE7953 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADF4001EBZ2 制造商:Analog Devices 功能描述:Evaluation Board For Pll Frequency Synthesizer 制造商:Analog Devices 功能描述:ADF4001 PLL SYNTHESIZER EVAL BOARD
EVAL-ADF4002EB1 制造商:Analog Devices 功能描述:EVAL BOARD - Bulk
EVAL-ADF4002EBZ1 功能描述:BOARD EVAL FOR ADF4002 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
EVAL-ADF4007EBZ1 功能描述:BOARD EVALUATION FOR ADF4007EB1 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADF4106EB1 制造商:Analog Devices 功能描述:PLL, Frequency Synthesizer